Fluorescent Pigments and Heat: Why Processing Temperature Decides Brightness
Category: Fluorescent pigment
A fluorescent colour can lose its brightness in the machine before it ever sees daylight. This article explains why heat degrades the dye, how to read a series heat limit — DX up to 195 °C — and how to choose and run a series for injection moulding, extrusion, masterbatch and powder coatings.
1. Brightness Is Decided Before the Colour Ever Sees Daylight
A daylight fluorescent pigment gets its extra brilliance from a dye dissolved in a resin, forming a solid solution. The dye absorbs ultraviolet light and gives it back as visible light — that is the glow. But the same absorbed energy can also break the dye down, permanently, into a structure that no longer fluoresces. Heat makes that breakdown faster, and it can happen inside the processing machine, long before the finished part is ever exposed to sunlight.
That is why a heat problem and a lightfastness problem look alike on the finished part — both end in a duller colour — but they are not the same problem. Lightfastness is about what sunlight does to the colour over weeks and months outdoors, as explained in article #1 on lightfastness. Heat damage is about what the process does to the dye in minutes, before the part leaves the factory. Fix the wrong one and the colour stays dull.
2. The Heat Limit Is a Hard Ceiling, Not a Target
Every fluorescent pigment series has a heat-resistance limit, and it is a hard limit, not a reference value. Once the processing temperature goes past the limit for the series in use, the fluorescent dye degrades: brightness falls and the hue shifts. The limit is set by the series, so the first check in any selection is the temperature — not the colour card.
Two consequences follow. First, a series is not interchangeable on temperature: a process that runs hotter than a series' limit needs a different series, a cooler process, or a different resin — not a hope that a short excursion will be forgiven. Second, the limit applies to the temperature the pigment actually experiences, not the temperature written on a dial. That distinction is the subject of the next section.
3. Melt Temperature Is Not the Barrel Set Temperature
In injection moulding and extrusion, the temperature that matters is the melt temperature — the temperature of the molten material itself. The barrel set temperatures are only the starting point for reaching it. Shear in the screw, a long residence time, a hot spot in a heater band, or a melt that sits in a hot runner can all push the real melt temperature above the set temperatures, sometimes by enough to cross a series limit without any alarm going off.
- Measure the melt, not the set point. Check the actual melt temperature with a melt probe or a purged sample at the nozzle or die, at the real running conditions — not at idle, and not only at start-up.
- Count the time at temperature, too. A melt that sits hot for a long residence time — a slow cycle, a large barrel running a small shot, a long stop — accumulates heat damage even if the peak temperature never looks extreme. Short, steady running is kinder to the dye than long, hot pauses.
- Change one thing at a time. If a trial part comes out dull, lower the melt temperature first, then shorten the residence time, and re-check the colour after each change. Changing both at once hides which one was the cause.
4. Thermoplastic and Thermoset Series Meet Heat Differently
Deping's fluorescent pigment guide lists seven series, and they fall into two resin types. A thermoplastic series softens and melts when heated; a thermoset series does not melt on heating and keeps its particle form during processing. That difference decides what the heat limit has to protect.
| Resin type | Series | Main applications (from the selection guide) |
|---|---|---|
| Thermoplastic | DX | PP, PE, PVC, water-based coatings |
| Thermoplastic | DZ | Injection moulding and extrusion — PP, PE, PET, PVC — and powder coatings |
| Thermoplastic | DQ | Blow-moulded bottles, masterbatch |
| Thermoset | DP | Inks, coatings, powder coatings |
| Thermoset | DFQ | PP, PE, PVC, masterbatch, inks, coatings, powder coatings |
| Thermoset | DFB | Inks, coatings |
| Thermoset | DFL | PP, PE, PVC, TPR, EVA, rubber |
For a thermoplastic series, the pigment melts with the resin, so the melt temperature is the temperature to control. For a thermoset series, the pigment stays as particles and has to survive the whole process as particles — in powder coatings, for example, that means surviving the full cure cycle. Either way, the check is the same: the highest temperature the pigment will actually experience, held for the time it will actually experience it, must sit within that series' TDS limit. The guide's note on the products page also lists a DS series; its detailed specifications are available on request from the TDS, so this article gives no figures for DS.
5. Choosing by Process: Temperature First, Then Series
The selection guide's rule is to start from the application and check the temperature first. The table below follows that guide; the temperature check in the right-hand column is the decisive one.
| Application | Start with | Decisive temperature check |
|---|---|---|
| Injection moulding and extrusion (PP, PE, PET, PVC, TPR, EVA) | DX or DZ | Melt temperature must not exceed the chosen series' limit; DX up to 195 °C |
| Masterbatch | DQ (designed for this); DFQ also usable | The masterbatch carrier resin must match the final product's base resin; the compounding temperature must stay within the series limit |
| Blow-moulded bottles and containers | DQ | Pre-disperse into masterbatch first — it colours more evenly than dry-blending pigment powder at the machine |
| Water-based coatings and water-based pastes | DX | DX is the series listed for water-based coatings in the guide |
| Powder coatings | DZ, DP or DFQ | The coating's cure conditions must not exceed the pigment's heat tolerance — the pigment has to live through the whole cure, as in article #6 on curing |
| Printing inks and coatings | DP or DFB; DFQ also covers inks and coatings | Test for bleeding in solvent-based systems before production |
| Rubber, TPR, EVA | DFL | Confirm compatibility in the actual formulation |
One worked example shows how the rule bites. A standard powder-cure schedule can reach about 200 °C at part metal temperature (article #6). A fluorescent-coloured film cured at that temperature is already past the DX ceiling of 195 °C, even if the resin itself would tolerate it — so DX is not the series for that cure, and the choice has to move to a series whose TDS limit covers the cure, or the cure has to move to a lower-temperature system. When the colour is the product, the pigment's ceiling — not just the resin's cure window — sets the top of the oven.
A white base also matters to the result, though it is not a heat question: white shows fluorescent brightness best, and a dark base absorbs it. Always test on the actual base colour you will sell on, not on a white trial plaque alone.
6. Running the Process: Keep It Cool and Short
Once the series is chosen, the process still has to be run inside its limit. Four habits cover most of the risk:
- Start at the low end. Begin with the lowest melt or cure temperature that still fills, flows or cures the part, and only raise it if the part genuinely needs it. A temperature that is merely convenient is not a reason to run hotter.
- Keep residence time short and steady. Avoid long holds at temperature, oversized barrels running small shots, and long stops with hot melt sitting in the machine. Purge before restarting after a stop, and check the first parts after the restart separately.
- Do not re-heat the same material and expect the same colour. Every extra pass through heat — regrind, reprocessing, a second cure — adds another heat history to the dye. If regrind is used, check the brightness of the reprocessed parts against a first-pass reference, and do not assume it will match.
- Record the temperature you actually ran. Note the measured melt temperature and the residence time for the trial that produced the approved colour. The next order should repeat those conditions, not just the colour number.
7. What Heat Damage Looks Like — and How to Prove It
Heat-damaged fluorescent colour is usually dull rather than wrong in an obvious way: brightness falls, the hue shifts, and the loss is often uneven across the part — worse where the melt was hottest or sat longest. Because the dye is already degraded, no amount of extra pigment in the next batch restores the brightness that was lost in the machine; the fix is in the process, not in the loading.
- Compare against a known-good reference. Keep a trial plaque or part made at a confirmed-safe temperature, and compare suspect parts against it under the same light. A side-by-side comparison catches a dull part that a memory of the colour would miss.
- Check the colour after processing, not before. A colour match made on unprocessed pigment or on a cold mix says nothing about what survives the machine. The approval sample must go through the real process, at the real temperature and residence time.
- Separate heat from light. If a part is dull straight out of the machine, the cause is heat, not sunlight — do not send it for a lightfastness test to explain it. If it is bright at first and fades outdoors, that is the lightfastness question from article #1, and the remedies are different.
8. Frequently Asked Questions
Q1: What is the highest processing temperature for DX series in injection moulding?
Up to 195 °C. Both the melt temperature and the time spent at high temperature must stay within that limit, as given in the series TDS. Processing above the limit degrades the fluorescent dye, and the part shows it as lower brightness and a shifted hue.
Q2: Can I run hotter than the limit for a short time?
No. The limit is a ceiling, not an average: a short excursion above it still degrades the dye, and time spent at the ceiling also counts. If the process needs a higher temperature, change the series, the resin or the process — do not run the same series hotter and hope the short time saves it.
Q3: My melt runs at about 210 °C — can I still use a fluorescent pigment?
Not DX: 210 °C is already past its 195 °C ceiling. Do not assume another series is automatically higher — check that series' TDS limit first, and only proceed if the limit covers your melt temperature with margin. If no series covers it, the honest options are to lower the process temperature, change the base resin, or accept that this process cannot carry a fluorescent colour at that temperature. Trial a part and compare it against a known-good reference before committing to a production run.
Heat is the first test a fluorescent colour has to pass, and it is passed in the machine — not in the showroom. Choose the series by its temperature limit, measure the temperature the pigment actually experiences, keep it cool and short, and prove the colour on a part that went through the real process.