Fluorescent Pigment Migration: Why Bright Colours Bleed into Their Neighbours
Category: Fluorescent pigment
A fluorescent colour sometimes turns up where it should not be: a pale part stained pink, a mark left on the packaging, neighbouring parts staining each other. That is migration — the dye that colours the pigment is dissolved in the resin, and with the help of plasticiser, solvent, heat and time it moves. This article explains how migration happens, the four situations where it strikes most often, how thermoset and thermoplastic series differ, and how to test before production and trace a failure.
1. The short answer: migration is dye on the move, not colour lost
First, the answer: migration is the dye inside a fluorescent pigment moving somewhere it should not be. The colour in a fluorescent pigment comes from a dye dissolved in a resin, forming a solid solution — the dye is not chemically tied to the resin. Given the right conditions, dye molecules slowly move into neighbouring plastic, coating, ink or packaging. The original part turns paler and duller, while a place that should have no colour picks up a fluorescent stain.
This is not the same as fading: fading is the dye being destroyed by light and heat, so the colour pales where it is. Migration is the dye surviving — just in the wrong place. Telling the two apart is the first step to tracing the problem.
2. How migration happens: dye, a path, and time
Migration needs three things at once; without any one of them it hardly happens:
- Dye that can move. The brightness of a fluorescent pigment comes from dye dissolved in resin, and dye molecules are mobile by nature. That is a property of fluorescent pigments, not a fault in one batch.
- A path to travel on. Plasticiser, solvent and resin softened by heat all open the way for dye molecules. Plasticiser is the biggest helper: it softens the resin and frees the polymer chains, and the dye travels along with it.
- Enough time and temperature. Migration is not instant. The warmer it is and the longer the contact lasts, the further the dye goes. A few months in a warm warehouse shows far more than a check made the day a part comes off the line.
That is why migration rarely shows on a fresh sample — a sample can look perfect and still fail after production, transport and storage. A migration test measures the result under real conditions, not the colour at the moment of moulding.
3. The four situations where it strikes most often
| Situation | Why migration is likely | What it looks like |
|---|---|---|
| Plasticised soft PVC | High plasticiser content; the resin is soft and its chains move freely | Bright colour bleeds into neighbouring pale areas on toys, cables, flooring and artificial leather |
| Rubber goods | Rubber is soft and porous, and dye diffuses through it easily | A coloured rubber part stains the pale part it touches |
| Solvent-based inks and coatings | Solvent carries the dye out, most of all before the film is fully dry | Colours bleed into each other on overprinting, with softened edges and cross-staining |
| Contact in storage and packaging | Bright parts pressed against pale parts or packaging for a long time | Only found when the pack is opened: the pale part or the inside of the packaging is stained |
All four share the same pattern — “contact plus time”. A fluorescent part on its own is usually fine; put it against a pale part, in solvent, or under heat for weeks, and the problem appears. Choose and test for the harshest real use, not the easiest one.
4. Thermoset vs thermoplastic series: does migration differ?
Deping fluorescent pigments fall into two resin types: thermoplastic series DX, DZ and DQ, and thermoset series DP, DFQ, DFB and DFL. As a general principle, a cured thermoset resin forms a crosslinked network that usually holds the dye more tightly, so the dye moves less easily; a thermoplastic resin has no crosslinked network, so the dye has more room to move.
But that is only a general principle, not a guarantee: a thermoset series can still migrate with a strong solvent, a high plasticiser level or long hot contact, and a thermoplastic series can stay stable for years in a dry, plasticiser-free, contact-free use. What decides migration is the whole system — resin, plasticiser, solvent, temperature, contact and time — not the series name alone. Choose the series by application, following the selection guide, and always verify migration in the real formulation before production.
5. How to test before production: four steps, and do not trust the colour chip alone
- Make the sample in the real formulation. Use the actual resin, plasticiser, solvent and processing conditions. A pigment colour chip cannot show migration.
- Run a contact test. Press the fluorescent sample tightly against a white or pale sample — or the actual packaging material it will touch — store it at a temperature the product may meet in use, and check afterwards whether the pale face is stained. Agree the temperature and time with the customer in advance, and record them.
- Add solvent and heat-ageing checks. For solvent-based systems, check for bleed after rubbing or soaking; keep a reference sample from the same batch under the same conditions but without contact or heat, so the comparison means something.
- Keep the sample and the record. Write down the temperature, time and contact materials. When a customer asks, or a production batch fails, that record is what you compare against.
There is no single universal set of test conditions: toys, cables and inks face different storage temperatures and service lives. The right way is to agree with the customer what counts as a pass, write it down, and then test — not to argue about the standard after the test.
6. How to reduce migration: series, formulation and storage
- Series: choose by the application system first (injection moulding, extrusion, masterbatch, inks and powder coatings each have their matching series); do not choose by colour alone. Once the series is fixed, verify migration in the real system.
- Formulation: plasticiser level is one of the deciding factors in the customer's formulation — reduce it where possible. For solvent-based systems, mind the solvent choice and drying conditions. These are formulation decisions for the customer to verify; this article gives no dosage figures.
- Separation and storage: store bright parts apart from pale parts and avoid long direct contact; test the packaging material for contact staining before fixing it; avoid long hot storage of finished goods.
One common mistake is “the colour is not bright enough, so add more pigment”. With migration, adding more does not necessarily help — the more dye there is, the more dye there is to migrate, and the staining can get worse. Find the path first, then decide about dosage.
7. When migration has already happened: separate the cause before you act
- First confirm it is migration. Fluorescent colour appearing next door, with the original going paler, is migration. Colour paling in place, with nothing new next door, is more likely fading (light or heat damage to the dye). The causes and the fixes are completely different.
- Then find the path. Ask four questions: what pale part or packaging did it touch? Did the plasticiser or solvent change? What were the storage temperature and time? Is the whole batch affected, or only the pieces that were stacked together? The answers usually point straight at the path.
- Only then change the formulation or the series. Separate storage, a barrier layer, a formulation change or a different series all need to be re-tested by the method in Section 5 and confirmed before production. Do not change several variables at once, or you will not know which one worked.
8. Frequently Asked Questions
Q1: Is migration the same thing as fading?
No. Fading is the dye being destroyed by light or heat, so the colour pales where it is and nothing new appears next door. Migration is the dye surviving but moving: the original goes paler and fluorescent colour shows up where it should not be. Work out which one it is before tracing the cause.
Q2: Does a thermoset series never migrate?
No. A crosslinked network usually holds the dye more tightly, but it is not a guarantee. With a strong solvent, a high plasticiser level or long hot contact, a thermoset series can migrate too. The series can narrow the risk; it cannot replace testing in the real system.
Q3: The sample looked fine — can production still fail?
Yes. Migration needs time and temperature, so a fresh sample often looks fine. The test must reproduce the real storage and transport conditions (temperature, time and contact materials), with a reference sample kept for comparison. Testing only the colour straight off the mould is not a migration test at all.
In one line: the brightness of a fluorescent pigment comes from a dye, and dye walks. Choose by the system, test under real conditions, and do not let bright parts sit pressed against pale ones — preventing migration is cheaper than tracing it.